cokeaddict posted:

Thanks Colin,
Yes they are sitting right. Thanks for ur suggestion though. Cheers

I love it when you talk DIRTY ! Member: My Profile

cokeaddict posted:

Hi Roachie,
Thanks for the suggestion mate, If you asked me if i have raised the bonnet from the back plate, the answer is NO. The bonnet is sitting as it was meant to be. Also are the pins easily accessable without removing half the front body panels? if so, can these pins be purchased through nissan?
Cheers Angelo

I love it when you talk DIRTY ! Member: My Profile

Member - Roachie (SA) posted:

Angelo,
Sorry, I don't think I explained myself properly.....I was wondering if, when you have the bonnet lifted up (as you would to do any work under there), have you tried grabbing the bonnet at the side, near the hinge and seeing if there is any "play" in the hinge/s?
I've never taken a bonnet off, but would imagine the 2 pins are only accessible by removing the side mudguard/s. I'm sure Mr Nissan will sell you new pins for several hundred dollars!!!!LOL
Cheers

Click Image to Enlarge

There's only one thing more painful than learning from experience and that is NOT learning from experience! Member: My Profile

cokeaddict posted:

Ok thanks for the reply Roachie,
I havent done that as yet but now that you suggested it I will as soon as i get some free time or the missus starts nagging again, either way it wont be long ok !

As for Nissan's prices well i wont be worried too much mate, if its just a straight forward pin, I'll get the shop to make up some stainless steel ones for me

Might just get her muddy before iremove guards and stuff though, that way i can kill 2 birds with 1 stone.
Thanks again mate
Regards Angelo

I love it when you talk DIRTY ! Member: My Profile

cokeaddict posted:

So thell me Gerry, what exactly did you have to remove to get to the hinges?
I'm asking so i can work out how long the job will take.
Thanks for your advise mate
cheers angelo

I love it when you talk DIRTY ! Member: My Profile

Gerry posted:

The hardest bit is getting a socket or spanner into the recess where the hinge is attached to the car (not much room). Just make sure you either support the bonnet somehow before removing any bolts, or perhaps take the bonnet off altogether so the remaining bolts are a bit more accessible. But honestly mate, I really don't reckon it's worth it - a slight sideways pressure on the hinge, just enough to put an ever so slight bend in it so that there is some pressure on the hinge pin when closed is all it needs to stop the rattle.
Cheers
Gerry

cokeaddict posted:

Yep id agree with you about hardly worth it, but sometimes when carrying passengers its very annoying to hear such a loud crack after they compliment me on how good the condition of the car is in. But im wondering if you had to remove the metal plate above the bonnet where the wiper arms are.

Another thing please Gerry when you say to bend the tips just a tad, do you mean bend them so both bends are facing inwards towards the swing hing? im assuming thats what u meant so they can be used as a guide and actually touch the hinge when closed.

I love it when you talk DIRTY ! Member: My Profile

Gerry posted:

Sorry I took so long to reply but haven't been on the forum for a few days... when I say "hardly worth it" I meant it was hardly worth pulling the whole thing out and reworking the mechanism as I did that and it didn't fix it for long. No, I didn't have to take out the grille near the wipers. If you can imagine the hinge in the closed position, it would look something like a closed pair of scissors, by giving the whole mechanism a slight bend or twist (as I say, doesn't need much) so that there is a small amount of pressure at the hinge pin, then the rattle stops. I just put a large screwdriver between the two halves of the hinge with bonnet open, pushed slightly sideways and that's all it needed. You don't need to bend the hinge so it touches the sides or anything as all it needs is enough twist to put a bit of pressure on the hinge pin itself. Hope that explains a bit better - good luck
Cheers
Gerry

cokeaddict posted:

Thanks Gerry,
Yes its crystal clear now thanks for that mate.
Ill fiddle with it some time soon.Thanks again mate

Angelo

I love it when you talk DIRTY ! Member: My Profile